In September 2023, 1 Rotary Press 1(2)-900/2000CVP in Medicine Hat, AB

In September 2023, 1 Rotary Press 8-900/8000CVP in Crabtree, QC

In September 2023, 1 Rotary Press 1(2)-900/2000CVH in Nexkemia, QC

In July 2023, 1 Rotary Press 1(2)-900/2000CVH in Chertsey, QC

In June 2023, 1 Rotary Press 6-900/6000CV in Gagetown, New Brunswick

In May 2023, 1 Rotary Press 4(6)-900/6000CVH in St-Stanislas, QC

In April 2023, 1 Rotary Press 8-900/8000CVH in Prospect Valley, CO

In January 2023, 1 Rotary Press 3-900/3000CV in Brandenburg, KY

In January 2023 2 Rotary Presses 7(8)-900/8000CV at Fort Bend, TX

In December 2022 1 Rotary Press 2(4)-900/4000CV at Batesburg Leesville

In November 2022 1 Rotary Press 3-900/3000CVP at Pont-Rouge, QC

In October 2022 1 Rotary Press 1(2)-900/2000CVP at ST-Gabriel-de-Brandon, QC

In October 2022 6 Rotary Presses 8-900/8000CV at Québec City

In August 2022 a Rotary Press 1(2)-900/2000CV at Heard County, GA

In July 2022 a Rotary Press 4(6)-900/6000CVP at Mukilteo, WA

In July 2022 a Rotary Press 1(2)-900/2000CVP In Nova Scotia

In May 2022 a Rotary Press 1(2)-900/2000CVP In Germany

In May 2022 a Rotary Press 2-900/2000CV In Florida

In April 2022 four (4) Rotary Press 6-900/6000CV for Logan, UT

In March 2022 an 5(8)-900/8000CV for Newton County, GA 

In March 2022 a 6-900/6000CVP SS304 for a paper mill in Washington state

In March 2022 a 6-900/6000CV for Duncansville, PA

In February 2022, an 6-900/6000CV machine at Saanich, BC

In February 2022, an 8-900/8000CV machine at Dairy Farmers of America ST. George , UT

In February 2022, an 6-900/6000CV machine at Pincourt, QC 

In February 2022, an 4-900/4000CV machine at Geneseo, IL

In January 2022, an 1(2)-900/2000CV machine at Dresden, OH

In January 2022, an 4(6)-900/6000CV machine at Harrisburg, SD

In October 2021, an 8-900/8000CV machine at Atlantic City, NJ

In October 2021, an 8-900/8000CV machine at Yorktown, IN

In October we started a Rotary Press 4(6)-900/6000CVH and our new dry polymer system (Quickdraw) for a Biomethane site in Norway

In September, we started a full stainless-steel machine 6-900/6000CVP SS304 at a paper mill in the province of Quebec.

In September, we started 2 Fournier emulsion polymer systems POLYSYS-3/4-120V.

Buchanan, MI August 2021 1 Rotary Press 4-900/4000CV.

Warsaw, KY  March 2021  1 Rotary Press 1(2)-900/2000CV.

Bath, PA  April 2021  1 Rotary Press 2-900/2000CV.

Medford Lakes, NJ  March 2021  1 Rotary Press 2(3)-900/3000CV.

Pittsfield, MA March 2021  4 Rotary Press 6-900/6000CV.

Celina, TX October 2020.

Sanderson Farms, LA October 2020.

Enfield, CT June 2020.

Macon, GA Rocky Creek June 2020.

Macon, GA Rocky Lower Poplar 2020.

Slippery Rock, PA May 2020.

Eatonton, GA May 2020.

Circleville, OH May 2020.

Lethbridge, Alberta, February 2020.

Lillehammer, Norway December 2019.

Alberta Newsprint October 2019.

Cape May, NJ (Ocean City) June 2019.

In November 2017 we did the start-up of one FullAuto Filter press for Rio Tinto in Jonquiere, QC.

The filter press was installed to replace a vacuum drum filter in a continuous chemical process. The upgrade led to an increase in the % of solids in the material.

In August 2017 we did the start-up of one mechanized Filter press for Toda Advanced Materials at Sarnia, ON

In April 2017 we did the start-up of two 7 Channels futur 8 Rotary Presses at Becker, MN

“Dave Pesola, City of Becker Water/Wastewater Supervisor has commented “In the short time that the Fournier Rotary Presses have been in operation at our facility, Staff has been very pleased with the quality of bio solids produced, the ease of operation, and how quiet the equipment is. The low water usage compared to the belt presses we were using is also an added benefit. This has reduced the humidity in the press room which was contributing to problems with electrical and HVAC equipment.”

In January 2017 we did the start-up of three 6 Channels Rotary Presses at Murfreesboro, TN

They have a total of eight 6 Channels Rotary Presses.

In November 2016 we did the start-up of 2 Channels Rotary Press at Milan, TN

In October 2016 we did the start-up of 6 Channels Rotary Press at North Liberty, IA

Start Up performed by Fournier on Rotary Press including Electrical and Process Start-Up was very well done by Fournier Technicians.

Start-Up and Training was very professional.

Milan Fabijanic | Project Manager

TRICON CONSTRUCTION GROUP

In September 2016 we did the start-up of 1Channel futur 2 Rotary Press at Rock Valley, IA

In June 2016 we did the start-up of a 6 Channels Rotary Press at Billerica, MA.

This is their second Rotary Press, the previous one has been in operation since 2006.

In May 2016, we did the start-up of a 6 Channels Rotary Press at Killian Creek, NC.

This is their second Rotary Press, the previous one has been in operation since 2010.

In April 2016 we did the start-up of a 4 Channels Rotary Press at Weyauwega, WI.

In March 2016 we did the start-up of a 6 Channels Rotary Press at Greensboro, NC to dewater their ash slurry produced by their incinerator.